{"product_id":"speedybee-f7-v3-flight-controller-stack-with-50a-esc","title":"SpeedyBee F7 V3 Flight Controller \/ Stack with 50A ESC","description":"\u003cp\u003eWe sell the flight stack (FC+ESC) and the FC on its own – please select as required.\u003c\/p\u003e\n\u003cp\u003eHere is SpeedyBee’s flagship flight controller \/ ESC. Surely the most modern and connected stack available on the market to date.\u003c\/p\u003e\n\u003cp\u003eIt consists of the F7 V3 flight controller and the BL32 50A 4in1 ESC . The FC benefits from a STM32F722 processor , the BMI270 gyroscope , BMP280 barometer , a 500Mb Blackbox , 2 BECs (3.3V, 4.5V, 5V and 9V BEC) and 5 UARTs . Regarding the ESC, it features a striking CNC machined heatsink and it can withstand a continuous current of 50A and 55A peak for 5 seconds. With an F4 MCU, you can set the PWM frequency up to 128KHz. It operates under the Dshot 300\/600 protocol. The ESC is built with a TVS protective diode to absorb the voltage spike when you plug in the battery, or during crashes that block your props. SpeedyBee also provide a humongous 1500uF low ESR capacitor, ensuring clean data from the gyro to the FC.\u003c\/p\u003e\n\u003cp\u003eAs with previous SpeedyBee FCs, it has integrated Bluetooth \u0026amp; WiFi. S o you can carry out the complete configuration of your quad, including firmware flashing (Betaflight, INAV, or Emuflight), directly from your smartphone using the SpeedyBee App on the go. As it happens, this new V3 version of SpeedyBee’s flight controller comes with onboard 2-in-1 Bluetooth \/ WiFi which boasts 33% faster wireless data transfer than its predecessor. In addition, you will be able to retrieve Blackbox data directly in the field in just a few seconds. In short, no need for a computer! With 500MB of onboard memory, you never need to worry about running out of space on the Blackbox either . For purists, there is still a USB-C port present on the FC for setup via a computer.\u003c\/p\u003e\n\u003cp\u003eAs if that weren’t enough, this FC can support up to 8 motors for big X8 cinelifters. It also has solder-free plugs for your VTX, RX, camera, GPS, and 4x LED strips (available here ), enabling more rapid builds. If you hate soldering, this is the flight controller for you! If you are old school and prefer soldered connections, no bother, just flip the PCB over and start working on it.\u003c\/p\u003e\n\u003cp\u003eFor DJI digital FPV pilots, there is a connector present for plug and play connection with the DJI Air Unit.\u003c\/p\u003e\n\u003cp\u003eThis FC even has an innovative built in LiPo voltage indicator , so you can fly anywhere worry-free, even if you forgot to bring your cell checker! 4 LEDs are integrated into the FC allowing you to know the percentage indication of current battery capacity.\u003c\/p\u003e\n\u003cp\u003eThis stack has 30.5×30.5mm mounting holes and can be powered via a 3 to 6S LiPo battery\u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1500uF Low ESR Capacitor with TVS Protective Diode\u003c\/li\u003e\n\u003cli\u003e500MB Onboard Blackbox Flash memory\u003c\/li\u003e\n\u003cli\u003e8 Motor output perfect for X8 Cinelifters\u003c\/li\u003e\n\u003cli\u003e30.5 x 30.5mm Mounting Pattern\u003c\/li\u003e\n\u003cli\u003eFC LiPo Monitoring System\u003c\/li\u003e\n\u003cli\u003eSpeedyBee 50A 128K ESC\u003c\/li\u003e\n\u003cli\u003eCNC Heatsink Shield\u003c\/li\u003e\n\u003cli\u003eBuilt-in Barometer\u003c\/li\u003e\n\u003cli\u003e128KHz PWM\u003c\/li\u003e\n\u003cli\u003e4 LED Plugs\u003c\/li\u003e\n\u003cli\u003eF722 FC\u003c\/li\u003e\n\u003cli\u003eBuzzer\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003ePower Output:\u003c\/li\u003e\n\u003cli\u003e1) 10 groups of 5V output, three +5V pads and 1 BZ+ pad (used for Buzzer) on the front side, and 6 +5V output included in the connectors on the bottom side. The total current load is 2A.\u003c\/li\u003e\n\u003cli\u003e2) 2 groups of 9V output, one +9V pad on the front side and the other included in a connector on the bottom side. The total current load is 4A.\u003c\/li\u003e\n\u003cli\u003e3) Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load Supported. Designed for 3.3V-input receivers. Up to 500mA current load.\u003c\/li\u003e\n\u003cli\u003eWiFi Support, used for data transfer, e.g firmware flashing, and Blackbox analysis.\u003c\/li\u003e\n\u003cli\u003eI2C: Supported. SDA \u0026amp; SCL pads on the front side. Used for magnetometer, sonar, etc.\u003c\/li\u003e\n\u003cli\u003eSupport Flight Controller Firmware: BetaFlight(Default), EMUFlight, INAV\u003c\/li\u003e\n\u003cli\u003eESC signal M1 – M4 on the bottom side and M5-M8 on the front side.\u003c\/li\u003e\n\u003cli\u003eLED: Used for WS2812 LED controlled by Betaflight firmware.\u003c\/li\u003e\n\u003cli\u003eUART: 5 sets (UART1, UART2, UART3, UART4, UART6)\u003c\/li\u003e\n\u003cli\u003eDJI Air Unit plug: A full DJI Air Unit JST slot onboard\u003c\/li\u003e\n\u003cli\u003eBLE Support, used for Flight Controller configuration\u003c\/li\u003e\n\u003cli\u003eBuzzer: BZ+ and BZ- pad used for 5V Buzzer\u003c\/li\u003e\n\u003cli\u003eMounting: 30.5×30.5mm, 4mm hole size\u003c\/li\u003e\n\u003cli\u003eDimensions: 41(L) x 38(W) x 8.1(H)mm\u003c\/li\u003e\n\u003cli\u003eOSD: BetaFlight OSD w\/ AT7456E chip\u003c\/li\u003e\n\u003cli\u003eBlackBox: 500MB onboard data flash\u003c\/li\u003e\n\u003cli\u003eBetaFlight Camera Control Pad: Yes\u003c\/li\u003e\n\u003cli\u003eESC Telemetry: UART UART4 RX\u003c\/li\u003e\n\u003cli\u003ePower input: 3S – 6S Lipo\u003c\/li\u003e\n\u003cli\u003eTarget: SPEEDYBEEF7V3\u003c\/li\u003e\n\u003cli\u003eSmartPort: Supported\u003c\/li\u003e\n\u003cli\u003eBaro: BMP280 (I2C)\u003c\/li\u003e\n\u003cli\u003eMCU: STM32F722\u003c\/li\u003e\n\u003cli\u003eBoot button: Yes\u003c\/li\u003e\n\u003cli\u003eRSSI input: Yes\u003c\/li\u003e\n\u003cli\u003eIMU: BMI270\u003c\/li\u003e\n\u003cli\u003eUSB: Type-C\u003c\/li\u003e\n\u003cli\u003eWeight: 9G\u003c\/li\u003e\n\u003cli\u003eCurrent Sensor: Supported (Scale=490 Offset=0)\u003c\/li\u003e\n\u003cli\u003eMounting: 30.5×0.5mm, 4mm hole size\u003c\/li\u003e\n\u003cli\u003eDimension: 45.6(L)x40(W)x8.8mm(H)\u003c\/li\u003e\n\u003cli\u003eFirmware: SpeedyBee BL32 50A\u003c\/li\u003e\n\u003cli\u003eWeight: 19.2g with heat sink\u003c\/li\u003e\n\u003cli\u003eContinuous Current: 50Ax4\u003c\/li\u003e\n\u003cli\u003ePower input: 3S – 6S LiPo\u003c\/li\u003e\n\u003cli\u003eBurst Current: 55A(5S)\u003c\/li\u003e\n\u003cli\u003ePower output: VBAT\u003c\/li\u003e\n\u003cli\u003e1 4-Pin SH1.0 to SH1.0 Analog VTX Cable 60mm – Yellow and Blue\u003c\/li\u003e\n\u003cli\u003e1 4-Pin SH1.0 to 3+ 2-Pin JST1.25 FPV Cam\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIn the box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1x SpeedyBee F7 V3 Flight Controller\u003c\/li\u003e\n\u003cli\u003e1x 6-Pin SH1.0 GPS module Cable without connector – 100mm\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Speedybee","offers":[{"title":"Flight Stack: FC + 50A ESC","offer_id":58941335830860,"sku":"FC-SB-F7V3STACK","price":117.9,"currency_code":"GBP","in_stock":false},{"title":"Flight Controller","offer_id":58941335863628,"sku":"FC-SB-F7V3-AIO","price":59.5,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1087\/9952\/5196\/files\/SpeedyBee-F7-Stack-V3.jpg?v=1790287084","url":"https:\/\/dronepart.co.uk\/products\/speedybee-f7-v3-flight-controller-stack-with-50a-esc","provider":"My Store","version":"1.0","type":"link"}