{"product_id":"speedybee-f7-mini-20-20-flight-controller-stack-with-35a-esc","title":"SpeedyBee F7 Mini 20×20 Flight Controller \/ Stack with 35A ESC","description":"\u003cp\u003eHere is a new FC \/ Flight Stack suited to 2-4inch quads from SpeedyBee. Like their other flight controllers, this one works with their fantastic SpeedyBee App ( iOS App Store \/ Google Play ); allowing you to configure your newly built quad, fine-tune PID’s, and configure other parameters without a laptop, simply via your phone or tablet wirelessly.\u003c\/p\u003e\n\u003cp\u003eThe FC is compatible with a standard 20×20 mounting pattern, using either M2 or M3 fixings, which are included. Considering the board’s small size, the size of the solder pads is generous and well labelled making for an easier installation. The spec of the FC is typical for a current flight controller, so it uses a F7 CPU, the MPU6000 gyro, includes OSD and on board blackbox. It also has two independent voltage regulators. A 9V 2A output and 5V 2A output, making it compatible with DJI FPV air units and standard analog FPV.\u003c\/p\u003e\n\u003cp\u003eSpeaking of the ESC, in stack form it comes with a 4-in-1 35A ESC with on board current sensor (it supports a 45A burst current). The ESC comes pre-flashed with Blue Jay firmware, which supports 48k\/96k PWM frequency and Bidirectional Dshot. Via the SpeedyBee App, you can even configure the ESC settings wirelessly as well.\u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eHigh-performance F7 flight controller CPU\u003c\/li\u003e\n\u003cli\u003eReal 35A BLHeli_S DSHOT600 ESC\u003c\/li\u003e\n\u003cli\u003eBuilt-in Bluetooth 4.0 BLE chip\u003c\/li\u003e\n\u003cli\u003e20x20mm mounting pattern with support for M2\u0026amp;M3 installation\u003c\/li\u003e\n\u003cli\u003eSmartPort Use any TX pad of UART for the SmartPort feature\u003c\/li\u003e\n\u003cli\u003eBLE Support, used for Flight Controller configuration\u003c\/li\u003e\n\u003cli\u003eSupport DJI Digital Video transmitter\u003c\/li\u003e\n\u003cli\u003eLED pin Used for WS2812 LED\u003c\/li\u003e\n\u003cli\u003eBluetooth Capabilities\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eMCU: STM32F722IMU\u003c\/li\u003e\n\u003cli\u003e(Gyro): MPU6000\u003c\/li\u003e\n\u003cli\u003eUSB Port Type: Type-C\u003c\/li\u003e\n\u003cli\u003eBarometer: N\/A\u003c\/li\u003e\n\u003cli\u003eOSD Chip” AT7456E chip\u003c\/li\u003e\n\u003cli\u003eBLE Bluetooth: Supported. Used for Flight Controller configuration\u003c\/li\u003e\n\u003cli\u003eFlash FC Firmware Wirelessly: Not supported. Please update firmware for this FC on the PC\u003c\/li\u003e\n\u003cli\u003eDownload\/Analyze Blackbox: Not supported. Please download and analyze Blackbox data on the PC\u003c\/li\u003e\n\u003cli\u003eDJI Air Unit Soldering Pads: Supported\u003c\/li\u003e\n\u003cli\u003eFlash(for BlackBox): 8MB\u003c\/li\u003e\n\u003cli\u003eCurrent Sensor: Supported Scale=250 Offset=-500\u003c\/li\u003e\n\u003cli\u003eBetaFlight Camera Control Pad: Yes(CC pad)\u003c\/li\u003e\n\u003cli\u003ePower Input: 3S – 6S Lipo\u003c\/li\u003e\n\u003cli\u003e5V Output: 6 groups of 5V output, five +5V pads and 1 BZ+ pad( used for Buzzer). The total current load is 2.5A.\u003c\/li\u003e\n\u003cli\u003e9V Output: 2 groups of 9V output, the total current load is 2A.\u003c\/li\u003e\n\u003cli\u003e3.3V Output: Supported. Up to 500mA current load.\u003c\/li\u003e\n\u003cli\u003eESC Signal Pads: M1 – M4\u003c\/li\u003e\n\u003cli\u003eUART: Full UART * 3(UART1, UART2, UART3)\u003c\/li\u003e\n\u003cli\u003eESC Telemetry: UARTR4(UART4)\u003c\/li\u003e\n\u003cli\u003eI2C: Not supported\u003c\/li\u003e\n\u003cli\u003eLED Pad: Used for WS2812 LED\u003c\/li\u003e\n\u003cli\u003eBuzzer:BZ+ and BZ- pad used for 5V Buzzer\u003c\/li\u003e\n\u003cli\u003eBOOT ButtonUsed to enter DFU mode\u003c\/li\u003e\n\u003cli\u003eRSSI Input: Not supported\u003c\/li\u003e\n\u003cli\u003eSmartPort: Use any TX pad of UART for the SmartPort feature.\u003c\/li\u003e\n\u003cli\u003eSupported Flight Controller Firmware: BetaFlight(Default), EMUFlight, INAV\u003c\/li\u003e\n\u003cli\u003eFirmware Target:  NameSPEEDYBEEF7MINI\u003c\/li\u003e\n\u003cli\u003eMounting: 20 x 20mm,  3.5mm hole diameter\u003c\/li\u003e\n\u003cli\u003eDimension: 30 x 30 x 7.5mm\u003c\/li\u003e\n\u003cli\u003eWeight: 5.7g\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Speedybee","offers":[{"title":"Flight Controller","offer_id":58941335535948,"sku":"FC-SB-F7M-AIO","price":43.99,"currency_code":"GBP","in_stock":false},{"title":"Flight Stack: FC + 35A ESC","offer_id":58941335568716,"sku":"FC-SB-F7MSTACK","price":94.6,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1087\/9952\/5196\/files\/SpeedyBee-F7-Mini-Stack.jpg?v=1790287083","url":"https:\/\/dronepart.co.uk\/products\/speedybee-f7-mini-20-20-flight-controller-stack-with-35a-esc","provider":"My Store","version":"1.0","type":"link"}