{"product_id":"holybro-pm06-v2-14s-micro-power-module","title":"Holybro PM06 V2-14S Micro Power Module","description":"\u003cp\u003eThe PM06 V2 is a cut down version of Holybro’s Full-Size PM07 power management board, making it suited to smaller platforms, for example racing drones. This is the 14S version of the PM06, the standard PM06 V2 supports up to 10S input.\u003c\/p\u003e\n\u003cp\u003eLike the PM07, this power board serves the purpose of providing a stable power supply along with voltage\/current monitoring to compatible flight controllers such as the APM, Pix32, Pixhawk, Pixhawk Mini, Pixhawk 4 or Durandal. It also functions as a power distribution board for connecting speed controllers too and includes a XT60 pigtail cable for connection with a battery. The board accepts an input power supply of 7-58V (Up to 14S LiPo) and outputs 5volts at 3amps. The board has a current rating of 120amps, which is split between four power output pairs, so suited to quadcopters. Lastly, there is a LC filtered output, which can be used to provide a clean power supply to FPV equipment.\u003c\/p\u003e\n\u003cp\u003ePX4 QGroundControl Setup\u003c\/p\u003e\n\u003cp\u003eConnector the Power Module to battery and connect the flight controller to your ground station via USB.\u003c\/p\u003e\n\u003cp\u003eOpen QGroundControl go Vehicle Setup and Power tab and Input the Number of Cells.\u003c\/p\u003e\n\u003cp\u003eEnsure the Voltage Divider \u0026amp; Amps per Volt is correct.\u003c\/p\u003e\n\u003cp\u003eFor more information with setting PX4 with QGround Control, refer to the PX4 Guide.\u003c\/p\u003e\n\u003cp\u003eArdupilot Mission Planner Setup\u003c\/p\u003e\n\u003cp\u003eOpen Mission Planner, go to Setup page and Battery Monitor tab and select the following:\u003c\/p\u003e\n\u003cp\u003eMonitor – “Analog Voltage and Current”\u003c\/p\u003e\n\u003cp\u003eSensor – “9: Holybro Pixhawk 4 PM”\u003c\/p\u003e\n\u003cp\u003eFor Pixhawk 4, Pixhawk 4 Mini, Pix32v5, Pix32, select the following: HW Ver – “0: CUAV V5\/Pixhawk 4 or API “\u003c\/p\u003e\n\u003cp\u003eHW Ver – “0: CUAV V5\/Pixhawk 4 or API “\u003c\/p\u003e\n\u003cp\u003eAlternatively, input the following in the parameter list\u003c\/p\u003e\n\u003cp\u003eBATT_VOLT_PIN: 0\u003c\/p\u003e\n\u003cp\u003eBATT_CURR_PIN: 1\u003c\/p\u003e\n\u003cp\u003eFor Durandal, select the following: HW Ver – “9: Durandal\/ZealotH743”\u003c\/p\u003e\n\u003cp\u003eHW Ver – “9: Durandal\/ZealotH743”\u003c\/p\u003e\n\u003cp\u003eBATT_VOLT_PIN: 16\u003c\/p\u003e\n\u003cp\u003eBATT_CURR_PIN: 17\u003c\/p\u003e\n\u003cp\u003eFor Pixhawk 5X You will need to use a digital power module like the that end with a “D” such as the PM02D.\u003c\/p\u003e\n\u003cp\u003eYou will need to use a digital power module like the that end with a “D” such as the PM02D.\u003c\/p\u003e\n\u003cp\u003eFor more information regarding setting up Power Module with Mission Planner. Please refer to the Ardupilot Wiki Page.\u003c\/p\u003e\n\u003cp\u003eCurrent Rating\u003c\/p\u003e\n\u003cp\u003eThe XT60 plug and 12AWG wire that PM06 comes with are rated for 30A continuous current and 60A instantaneous current (\u0026lt;1 minute). If a higher current is being used, the plug type and wire size should be changed accordingly. The specifications and models are as follows:\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eInput voltage: 2S-14S\u003c\/li\u003e\n\u003cli\u003ePower Module rated current: 60A\u003c\/li\u003e\n\u003cli\u003ePower Module max current: 120A (\u0026lt;60 sec)\u003c\/li\u003e\n\u003cli\u003eUBEC output: DC 5.1V~5.3V\u003c\/li\u003e\n\u003cli\u003eUBEC output current: 3A Max (Note: To ensure proper heat dissipation, UBEC output current needs to be limited to \u0026lt;2A when using 14S battery.)\u003c\/li\u003e\n\u003cli\u003eVoltage Divider: 18.182\u003c\/li\u003e\n\u003cli\u003eAmperes per Volt: 36.364\u003c\/li\u003e\n\u003cli\u003eDimensions: 35x35x5mm\u003c\/li\u003e\n\u003cli\u003eMounting hole: 30.5mmx30.5mm\u003c\/li\u003e\n\u003cli\u003eWeight: 24g\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIn the box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1x Power Module\u003c\/li\u003e\n\u003cli\u003e1x 80mm XT60 connector wire (pre-soldered)\u003c\/li\u003e\n\u003cli\u003e1x Electrolytic capacitor: 220uF 63V (pre-soldered)\u003c\/li\u003e\n\u003cli\u003e1x JST GH 6pin cable\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Holybro","offers":[{"title":"Default Title","offer_id":58941081780556,"sku":"FC-PM06-V2-14S","price":24.9,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1087\/9952\/5196\/files\/PM06-V2-14S-15019.jpg?v=1790286056","url":"https:\/\/dronepart.co.uk\/products\/holybro-pm06-v2-14s-micro-power-module","provider":"My Store","version":"1.0","type":"link"}