{"product_id":"holybro-atlatl-hv-5-8g-3w-pro-vtx-fpv-video-transmitter","title":"Holybro Atlatl HV 5.8G 3W Pro VTx FPV Video Transmitter","description":"\u003cp\u003eLegal Notice: Please check with your local authorities regarding the operation of this equipment before you purchase. Regulations on power output, usable frequencies and licenses’ to operate vary from region to region. By adding this product to your cart, you are confirming that you have read this notice, and that Flying Tech is in no way responsible for the actions of the operator while using this product.\u003c\/p\u003e\n\u003cp\u003eHolybro’s latest Atlatl VTX – updated with two button for easier setup and clear LED indicators.\u003c\/p\u003e\n\u003cp\u003eThis video transmitter offers a variable power supply, from 25mW (UK legal limit) up to 3W. Running at 3W generates a lot heat, so the VTX incorporates a built-in fan. It also has Pit Mode so that you can power up your VTX to change settings without knocking other pilots out of the air. There is also IRC Tramp which allows you to control your VTX via your flight controller to change channel and transmitting power remotely from your RC. The Atlatl Pro VTX comes with a durable MMCX connector and also with a pigtail SMA converter.\u003c\/p\u003e\n\u003cp\u003eWARNING: MAKE SURE TO INSTALL ANTENNA BEFORE TURNING ON THIS VIDEO TRANSMITTER\u003c\/p\u003e\n\u003cp\u003ePower light (Green) Blink once per sequence – 25mW 2 per sequence – 400mW 3 per sequence – 600mW 4 per sequence – 1.6W 5 per sequence – 3W\u003c\/p\u003e\n\u003cp\u003eBlink once per sequence – 25mW\u003c\/p\u003e\n\u003cp\u003e2 per sequence – 400mW\u003c\/p\u003e\n\u003cp\u003e3 per sequence – 600mW\u003c\/p\u003e\n\u003cp\u003e4 per sequence – 1.6W\u003c\/p\u003e\n\u003cp\u003e5 per sequence – 3W\u003c\/p\u003e\n\u003cp\u003eFrequency indicator light (Blue) Binary indicator. No lights means CH1, all lights means CH7\u003c\/p\u003e\n\u003cp\u003eBinary indicator. No lights means CH1, all lights means CH7\u003c\/p\u003e\n\u003cp\u003eFrequency band lights (Red) Blink once per sequence – Band A 2 per sequence – Band B 3 per sequence – Band E 4 per sequence – Band F 5 per sequence – Band R 6 per sequence – Band L 7 per sequence – Band X\u003c\/p\u003e\n\u003cp\u003eBlink once per sequence – Band A\u003c\/p\u003e\n\u003cp\u003e2 per sequence – Band B\u003c\/p\u003e\n\u003cp\u003e3 per sequence – Band E\u003c\/p\u003e\n\u003cp\u003e4 per sequence – Band F\u003c\/p\u003e\n\u003cp\u003e5 per sequence – Band R\u003c\/p\u003e\n\u003cp\u003e6 per sequence – Band L\u003c\/p\u003e\n\u003cp\u003e7 per sequence – Band X\u003c\/p\u003e\n\u003cp\u003eFunction Button Operation Instructions\u003c\/p\u003e\n\u003cp\u003eTo switch frequency – Short press the button to switch channel.\u003c\/p\u003e\n\u003cp\u003eTo switch the frequency band – Press and hold the button for 2 seconds to enter band changing mode. Short press the button to change the frequency band once enter the band changing mode.\u003c\/p\u003e\n\u003cp\u003eTo switch power – Short press the button to switch the power level. Green LED blinking times for each blinking sequence indicate the power level. Long press 2 seconds to enable PIT mode – green light stays on.\u003c\/p\u003e\n\u003cp\u003eOnce the configuration is finished, wait 8 seconds for it to save the settings.\u003c\/p\u003e\n\u003cp\u003eFrequency Table\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eFrequency: 5.8G 7 bands: A, B, E, F, R, L, X  Transmission Channel: 56\u003c\/li\u003e\n\u003cli\u003eOperating Mode: Key button, IRC Tramp (Pro)\u003c\/li\u003e\n\u003cli\u003ePower: Switchable: PIT, 25mW, 400mW, 600mW, 1.6W \u0026amp; 3W\u003c\/li\u003e\n\u003cli\u003eAntenna connector: MMCX\u003c\/li\u003e\n\u003cli\u003eInput Voltage: 7-36V (recommended 9-28V)\u003c\/li\u003e\n\u003cli\u003eCurrent Consumption: 1.3A\/12VDC @ 3000mW\u003c\/li\u003e\n\u003cli\u003eRF impedance: 50Ω\u003c\/li\u003e\n\u003cli\u003eInput video impedance: 75Ω\u003c\/li\u003e\n\u003cli\u003eInput video amplitude: CVBS 0.8~1.2VP-P\u003c\/li\u003e\n\u003cli\u003eVideo format: NTSC\/PAL\u003c\/li\u003e\n\u003cli\u003eDimension(L*W*H): 54x 28x 14mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIn the box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1x Atlatl HV Pro 5.8G 3000mW VTx\u003c\/li\u003e\n\u003cli\u003e1x 80mm SMA–MMCX Cable\u003c\/li\u003e\n\u003cli\u003e1x 70mm 6pin JST SH wire\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Holybro","offers":[{"title":"Default Title","offer_id":58941058941260,"sku":"FPV-TX-13040","price":69.7,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1087\/9952\/5196\/files\/Atlatl-HV-5.8G-Video-Transmitter.jpg?v=1790285972","url":"https:\/\/dronepart.co.uk\/products\/holybro-atlatl-hv-5-8g-3w-pro-vtx-fpv-video-transmitter","provider":"My Store","version":"1.0","type":"link"}